Everything works fine with old Cisco 2610 router + WIC-1T, but when putting the same WIC-1T to any slot of 2801 there is no link... Serial interface is detected and up, line protocol is up, but it is still not responding.
Configuration both of routers is the same, no changes with default clock rates or something... I've tested two different WIC-1T cards and there was the same behaviour, 2610 works fine, 2801 not...
Here is my config, sh ver, debug and all that can be helpful in diagnose.
2801#sh ver
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.3(8)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 06-Apr-05 12:34 by yiyan
ROM: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)
2801 uptime is 7 minutes
System returned to ROM by power-on
System image file is "flash:c2801-advsecurityk9-mz.123-8.T8.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco 2801 (revision 5.0) with 236544K/25600K bytes of memory.
Processor board ID FCZ092913UF
2 FastEthernet interfaces
1 Serial(sync/async) interface
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
2801#sh interfaces serial 0/3/0
Serial0/3/0 is up, line protocol is up
Hardware is GT96K Serial
Internet address is 62.87.128.94/30
MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:09, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 92
Queueing strategy: weighted fair
Output queue: 594/1000/64/92 (size/max total/threshold/drops)
Conversations 75/75/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1536 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
14 packets input, 336 bytes, 0 no buffer
Received 14 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1 packets output, 343 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=down
2801#sh run
Building configuration...
Current configuration : 1949 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 2801
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
ip cef
ip ips po max-events 100
ip domain name yourdomain.com
no ftp-server write-enable
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 192.168.231.1 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/3/0
bandwidth 2048
ip address 62.87.128.94 255.255.255.252
!
ip classless
ip route 0.0.0.0 0.0.0.0 62.87.128.93
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
control-plane
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
end
I've compared both releases and there should be no problem with 12.4, it has all of the 12.3T funcionality WS-X45-SUP7L-E and much more. With RAM there will be no problem, my 2801 has got 256MB while there's requirement of 128 megs.
没有评论:
发表评论